Instead of individual file protection, YEO has BootLock and ScreenLock, control mechanisms that prevent unauthorized system. Secure Delete will overwrite any file three times with a series of hexadecimal numbers: OAs, 05s, and 03s, before deleting it. OCTOBER 21, 1996 INFOWORLD 97. Recover My File 3.80 Serial Numbers. Convert Recover My File 3.80 trail version to full software.
Contents. Ordering Hardware POS Portal www.posportal.com (866) 940-4767 JR's POS Depot.
To initiate an order, partners call JR's or order via the ordering portal located at: Notes:. RPOWER Dealer is responsible for distributing devices to merchants. JR's will only ship to partners in bulk.
Readers must be affixed to the countertop for PCI compliance. The Phoenix Group.
Register as a buyer with The Phoenix Group if you do not have an account Notes:. Dealer is responsible for ordering the correct SKU. Readers must be affixed to the countertop for PCI compliance.
Press Obtain Serial Number. Once it obtains a serial, another box will pop up that says Obtain Serial Number is Successful (xxxx.xx.xxxxxx). Press OK Another box will come up that says Configuration not Set! - Use Setup Merchant Parameters. Press OK. Click on Setup then Merchant Parameters (or possibly Setup Information). Click Load New Parameters Another box will come up that says 'Attempt Activation?'
. Click Yes Another box will come up with options for I have My Deployment ID and I Do NOT Have My Deployment ID. Click I Have My Deployment ID. Type in the Deployment ID and press OK Verify the Merchant Information on the screen that pops up. Press Yes, This is the Correct Merchant if the information is correct. Add the NETePAY icon to the Startup menu for the user (or All Users) RPOWER Configuration Credcnx.ini.
Change HostIP=xxx:9000 where xxx is the name of the computer running NETePAY. Name: EMV Reader. Type: Normal. CC type: EMV Reader. Offline Floor Limit: 0.
FlashPay limit: 0 You can not run Offline or FlashPay with EMV devices If tips are accepted:. Ask for tip first: Check if you want the system to prompt for a tip after card is inserted. (Typical QSR setting). Print for tip & signature: Check.
Put $ over on tip: Check Initialize Reader Each EMV Reader needs to be initialized before use. This process installs software specific to your platform on the EMV reader.
In RPOWER,. Press Manager. Press System Setup. Press Credit Card Setup. Press Initialize Device. NOTE: This button will not light up until all other setup is complete, including the credcnx file After a couple minutes, RPOWER will prompt Init OK!. Follow above instructions to get to the pay screen.
Press Enter Card # The system will prompt 'Use EMV Keypad?' . Press Yes. One of the prompts on the EMV Keypad will ask 'Chip Card?' If it is a chip card, press the green button, if it is not a chip card, press the red button. Swipe and Manual Entry Settings for EMV Stations Starting with version 14020007, RPOWER is now sensitive to whether it will accept credit card swipes and manual card number entries when an EMV reader is installed. Note that dsiEMVUS being installed on a workstation causes RPOWER to consider the EMV device being present, so that not having one plugged in will not bypass that requirement.
The following RPOWER.ini settings have been added: CCEMVSwipeOK=1 Swipe with credit cards online. With dsiEMVUS installed, default is 0 for non-encrypted and 1 for encrypted. Forced offline adds one to the default. CCEMVOffSwipeOK=1 Swipe with credit cards forced offline. Overrides default from CCEMVSwipeOK. CCEMVManualOK=1 Manual entry with credit cards online. Default is CCEMVSwipeOK.
CCEMVOffManualOK=1 Manual entry with credit cards forced offline. Default is CCEMVOffSwipeOK.